A tankless water heater rarely fails without warning. It flashes a code, runs lukewarm, or shuts off halfway through a shower. The unit is telling you something, and most of the time the message is specific enough to point at the cause.
This guide covers what those messages usually mean, which fixes are safe to try yourself, what tankless water heater repair typically costs, and how to decide between repairing and replacing. If you’re still choosing a system, start with our tankless water heater installation and repair page. If you want the preventive side, read Tankless Water Heater Maintenance in Atlanta: What Most Homeowners Skip.
Why Did My Tankless Water Heater Stop Working?
Almost every no-hot-water complaint on a tankless unit traces back to one of five things.
- Scale on the heat exchanger. Minerals build up inside the unit and restrict flow and heat transfer. Some units flag this directly: Rinnai’s manual lists an “LC” code for scale buildup and tells the owner to flush the heat exchanger.
- A clogged inlet filter. A blocked screen cuts flow, and many units won’t fire below a minimum flow rate.
- Gas or ignition trouble. The burner can’t light, or the flame drops out. That points at gas supply, the igniter, or the flame sensor.
- Venting problems. Blocked or damaged exhaust or intake venting makes the unit shut itself down for safety.
- A failed sensor, fan, or valve. Temperature sensors and combustion fans are common replacement parts as units age.
What Tankless Water Heater Error Codes Mean
Error codes are not universal. The same number can mean different things on different brands, and sometimes on different models from the same brand. Always check your unit’s manual or the label inside the cover before acting on a code you found online.
To show how specific the codes can be, here is what Rinnai’s own manual for its R50LSi, R75LSi, and R94LSi models lists for a few common ones (Rinnai installation and operation manual):
| Code | Rinnai’s description | What it usually means for you |
|---|---|---|
| 11 | No ignition | The burner didn’t light: check gas type, airflow, and the combustion chamber |
| 14 | Thermal fuse | The unit overheated: restricted airflow, low flow, or a clogged heat exchanger |
| 16 | Over temperature warning | A sensor or scale problem |
| 32 | Outgoing water temperature sensor fault | A wiring, scale, or failed sensor issue |
| 61 | Combustion fan failure | The fan isn’t spinning freely or is failing |
| LC | Scale buildup in heat exchanger | The unit needs a flush |
The same manual states that the appliance “must be installed, serviced and removed by a trained and qualified person.” Reading a code is fine. Working inside a gas appliance is not a homeowner job.
What You Can Safely Check Yourself
Before you call anyone, five checks take about ten minutes and cost nothing.
- Power. Confirm the unit is plugged in and the breaker hasn’t tripped. Even gas models need electricity.
- Gas supply. Make sure the gas valve to the unit is open and other gas appliances are working.
- Other faucets. If hot water is weak everywhere, the problem is probably the unit or its filter. If it’s one fixture, look at that fixture first.
- Inlet filter. If you know how to close the water valves and access the screen, rinsing it is a standard maintenance step. Your manual shows where it is.
- Reset. Many units can be reset by cycling power. If the same code returns right away, stop and call a plumber.
If you ever smell gas, leave the house and call the gas company or 911 before anything else. For gas lines and leaks, see our gas leak repair page.
How Much Does Tankless Water Heater Repair Cost?
These are national figures from a third-party source, not Fix & Flow pricing. According to HomeAdvisor’s 2026 tankless water heater repair cost guide (updated June 2026), tankless repairs average about $600 and generally range from $75 to $1,300, with complex repairs reaching around $1,950.
| Repair | National range (HomeAdvisor) |
|---|---|
| Fuse | $50 – $75 |
| Pilot light | $75 – $150 |
| Pressure relief valve | $75 – $150 |
| Thermostat | $75 – $150 |
| Vent repair | $50 – $125 |
| Pipe repair | $100 – $350 |
| Gas valve | about $350 |
| Flushing and descaling | $150 – $300 |
Notice what the cheap end has in common: small parts and routine service. The expensive end is the heat exchanger and gas components. That’s why scale matters. A flush costs a fraction of what a scale-damaged heat exchanger does, and Atlanta homeowners who skip it tend to find out in year six or seven. For what Fix & Flow charges, contact us for information.
Repair or Replace?
HomeAdvisor’s guidance is a reasonable rule of thumb. Repair makes sense when the unit is under about 10 years old with no history of major problems. Replacement deserves a hard look when repair costs approach half the price of a new system, the unit is past roughly 15 years, or you’re seeing frequent error codes and persistent leaks despite regular maintenance.
Two Atlanta-specific points:
- Warranty first. Many parts and heat exchangers carry manufacturer warranties, and some require professional installation or documented service. Check before paying for a repair.
- Replacement is a bigger decision than a swap. It’s a chance to reconsider capacity, venting, and gas line size. Our tankless installation cost guide walks through what drives that price, and our guide to repairing vs. replacing a water heater covers tank units. If you’re weighing options, our hybrid water heater page covers a third choice, and our water heater repair page covers conventional tank systems.
Replacing a water heater in the city of Atlanta can require a permit. We cover that in Do I Need a Permit to Replace My Water Heater in Atlanta?
Who Can Fix a Tankless Water Heater?
A licensed plumber who works on tankless systems regularly, and who can handle the gas, venting, and water sides of the job in one visit. Tankless failures often cross those lines. A code that looks like a part failure can turn out to be a venting problem, and a “bad heater” can turn out to be scale. Having one team diagnose all three saves repeat trips. Fix & Flow has served Atlanta since 2010 and does not use plumbing subcontractors, so the plumber who diagnoses your unit is the one who repairs it.
If scale keeps coming back, treating the water may be part of the answer. See our water filtration page and our guide to what’s in Atlanta’s tap water.
Get Your Tankless Water Heater Looked At
If your unit is showing a code, shutting off mid-use, or running cold, a diagnosis is the fastest way to know whether you’re looking at a flush or a bigger repair. Book a service visit, call or text (404) 800-3569, or contact us. Estimates usually require a service fee, which is applied to the job cost if you hire us.
FAQ
Why did my tankless water heater stop working?
The most common causes are scale buildup on the heat exchanger, a clogged inlet filter, ignition or gas supply problems, blocked venting, and failed sensors or fans. The error code on the display, checked against your model’s manual, usually narrows it down.
What do tankless water heater error codes mean?
It depends on the brand and model. For example, Rinnai lists code 11 as no ignition, code 14 as a thermal fuse fault, and LC as scale buildup in its R50LSi, R75LSi, and R94LSi manual. Check your own unit’s manual rather than a generic chart.
How much does tankless water heater repair cost?
Nationally, HomeAdvisor reports an average of about $600, with a typical range of $75 to $1,300. Simple parts and flushes sit at the low end, while gas valves and heat exchanger work cost more. For Fix & Flow pricing, contact us for information.
Can I repair a tankless water heater myself?
Basic checks like power, the gas valve, the inlet filter, and a reset are reasonable. Work on gas, venting, and internal parts should be done by a trained, qualified person.
Do tankless water heaters need maintenance?
Yes. Manufacturers call for periodic flushing to remove scale, and inlet filters need cleaning. Skipping this is a leading cause of overheating codes and heat exchanger failure.
Should I repair or replace my tankless water heater?
Repair is usually the better value for a unit under about 10 years old. Consider replacement when repairs approach half the cost of a new system, the unit is past about 15 years, or problems keep returning.